100% Original Xhorse BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC
100% Original Xhorse BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC
This is 100% Original Xhorse BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC.
offer top quality 100% Original Xhorse BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC
Wholesale Top quality BENZ ECOM DoIP Diagnostic and Programming Tool, Super DSP3+ Odometer Correction Tool, VAS 5054A ODIS GM Tech2, Scania VCI3
images of 100% Original Xhorse BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC
This VVDI2 with Activated Software List:
VB-01 BMW OBD
VB-02 BMW CAS4
VB-03 FEM/BDC Function
VP-01 Porsche immo data tool
VJ-01 Passthru J2534
VK-01 Transponder Programmer
VVDI2 BMW Functions:
EEPROM/KM/Synchronization Codes (OBD)
Read EEPROM / Write EEPROM
Read KM / Write KM
Synchronize DME-CAS, CAS-ELV
Key Learn
Get Key Info
Write Key Info
Load Key Info / Save Key Info
Prepare dealer key with programmer
Prepare dealer key with ignition switch
Add key
Program Key Info
Repair Keyless Key
Enable Key / Disable Key
Clear DTC / Clear Shadow
File Make Key
EWS1/EWS2/EWS3/EWS4
CAS1/CAS2/CAS3/CAS3+/CAS4
Unlock Key
Unlock with key info file
Unlock with CAS1/CAS2/CAS3/CAS3+ EEPROM
File Change KM
EWS3/EWS4
CAS1/CAS2/CAS3/CAS3+ CAS4
Cluster (E Series): M35080 EEPROM dump
Cluster (F Series)
CAS Repair
CAS1(0K50E) OBDII Repair
ISTAP4* Version OBDII Repair
VVDI2-BMW FEM/BDC System (Function released and available)
Users can refer to following information (3 steps for make keys:get key info->programming FEM/BDC system->make keys)
1.support make new key with ignition switch(support add spare key and all key lost, all key lost require ISN)
2.support reset FEM/BDC KM(cluster require reset manually)
3.support erase key(after erase the key position become blank position)
4.support backup coding
5.support restore coding
Notes:
1. Backup coding and restore coding can direct operation generally.
2. Add keys, reset KM, erase key must programming FEM/BDC system first
3. In FEM/BDC interface, if 'get key info' the type not support, it will show:customer should use "BMW E-sys software" program FEM/BDC system.then programming FEM/BDC system with VVDI2-BMW
4. When operation on 'programming FEM/BDC system'interface,please don't close this software window until all procedures completed.
5. Programming FEM/BDC system, require soldering and get eeprom.（FEM 95128 chip, BDC 95256 chip）usually there are 2 same chips on the module, please refer to the software diagram, select the correct one.
6. Programming FEM/BDC system,must restore the original eeprom, restore coding.if cannot restore coding or after restore coding assemble FEM/BDC module back to car,but with problem(such as the remote control cannot start the car
or the car with window problem)please use "BMW E-sys software" coding for FEM/BDC system
7. If connect power to FEM/BDC module, but the relay keep ringing,please contact technical support for help.usually operation on FEM/BDC should be ok,just need to programming.
1. VVDI 2 Main Interface
2. 5th BDM Programmer
3. OBD2 cable
4. CAS Plus (additional part, need to buy alone CAS Plug for VVDI2 BMW or Full Version : 84.99usd)
5. Remote Programmer
6. USB Cable
Go to Buy: 100% Original Xhorse BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC